您好,歡迎光臨萊州kaiyun機械有限公司官方網站!

服務熱線

400-879-1999

你所在位置: 首頁 >> kaiyun > 公司新聞 >
公司新聞

混凝土攪拌車裝載問題的常見 處理方法

來源:http://www.skar-bnat.com/ 時間:2021-12-24

1.裝載時連接緊急驅動軟管,依靠其它攪拌車的動力。驅動拌筒旋轉並將混凝土排出。但是若減速器同時發生故障時,則不可采用此法。具體操作步驟如下:
1. Connect the emergency drive hose during loading and rely on the power of other mixer trucks. Drive the mixing drum to rotate and discharge the concrete. However, if the reducer fails at the same time, this method cannot be used. The specific operation steps are as follows:
(1)準備好一根緊急驅動軟管,卸下接管和接頭蓋;
(1) Prepare an emergency drive hose and remove the connecting pipe and connector cover;
(2)故障車(被驅動車)的操作:將故障混凝土攪拌車的發動機熄火;將緊固螺母朝左旋鬆;再將旋鈕朝右旋轉,直到不能再旋為止;將高壓軟管從馬達接頭處卸下;
(2) Operation of the failed truck (driven truck): turn off the engine of the failed concrete mixer; loosen the fastening nut to the left; turn the knob to the right until it can no longer be screwed; remove the high-pressure hose from the motor connector;
(3)救援車(驅動車)的操作:將操作手柄至於空檔位置;將發動機熄火;將高壓軟管從高壓油管處卸下;將緊急驅動軟管接到高壓油管上;用緊急驅動軟管上的接頭蓋將驅動車的高壓軟管蓋起,以防漏油。啟動救援車的發動機。將救援車的操作手柄撥至“出料”位置,使故障車內的混凝土排出。緊急驅動完畢後,使兩車各自恢複原狀。
小型混凝土攪拌車
(3) Operation of rescue vehicle (drive vehicle): set the operating handle to the neutral position; shut down the engine; remove the high-pressure hose from the high-pressure oil pipe; connect the emergency drive hose to the high-pressure oil pipe; cover the high-pressure hose of the drive vehicle with the connector cover on the emergency drive hose to prevent oil leakage. Start the engine of the rescue vehicle. Turn the operating handle of the rescue vehicle to "discharge" Position so that the concrete in the failed vehicle can be discharged. After the emergency drive, restore the two vehicles to their original state.
2.減速機損壞。如在工作中出現減速機突然損壞,首先需將攪拌筒內的混凝土排出,以防出現凝固現象;其次再更換減速機,也可聯係生產廠家。
2. The reducer is damaged. If the reducer is suddenly damaged during operation, first discharge the concrete in the mixing drum to prevent solidification; Secondly, replace the reducer, or contact the manufacturer.
3.柱塞泵發生故障。非裝載時換上新的柱塞泵,使拌筒恢複正常運轉。
3. The plunger pump fails. When not loaded, replace with a new plunger pump to restore the normal operation of the mixing drum.
4.液壓管接頭處滲漏。將接頭拆下,更換密封圈,重新擰緊即可。
4. Leakage at the hydraulic pipe joint. Remove the connector, replace the sealing ring and retighten it.
上一篇:選擇5方攪拌車往往忽略的5個地方
下一篇:混凝土攪拌車的這些小問題你都在乎了嗎?
tag:混凝土攪拌車,小型混凝土攪拌車,全自動混凝土攪拌車
當前位置: 首頁 - kaiyun > 公司新聞 >

混凝土攪拌車裝載問題的常見 處理方法

作者:中科kaiyun混凝土攪拌車廠家 時間:2021-12-24

1.裝載時連接緊急驅動軟管,依靠其它攪拌車的動力。驅動拌筒旋轉並將混凝土排出。但是若減速器同時發生故障時,則不可采用此法。具體操作步驟如下:
1. Connect the emergency drive hose during loading and rely on the power of other mixer trucks. Drive the mixing drum to rotate and discharge the concrete. However, if the reducer fails at the same time, this method cannot be used. The specific operation steps are as follows:
(1)準備好一根緊急驅動軟管,卸下接管和接頭蓋;
(1) Prepare an emergency drive hose and remove the connecting pipe and connector cover;
(2)故障車(被驅動車)的操作:將故障混凝土攪拌車的發動機熄火;將緊固螺母朝左旋鬆;再將旋鈕朝右旋轉,直到不能再旋為止;將高壓軟管從馬達接頭處卸下;
(2) Operation of the failed truck (driven truck): turn off the engine of the failed concrete mixer; loosen the fastening nut to the left; turn the knob to the right until it can no longer be screwed; remove the high-pressure hose from the motor connector;
(3)救援車(驅動車)的操作:將操作手柄至於空檔位置;將發動機熄火;將高壓軟管從高壓油管處卸下;將緊急驅動軟管接到高壓油管上;用緊急驅動軟管上的接頭蓋將驅動車的高壓軟管蓋起,以防漏油。啟動救援車的發動機。將救援車的操作手柄撥至“出料”位置,使故障車內的混凝土排出。緊急驅動完畢後,使兩車各自恢複原狀。
小型混凝土攪拌車
(3) Operation of rescue vehicle (drive vehicle): set the operating handle to the neutral position; shut down the engine; remove the high-pressure hose from the high-pressure oil pipe; connect the emergency drive hose to the high-pressure oil pipe; cover the high-pressure hose of the drive vehicle with the connector cover on the emergency drive hose to prevent oil leakage. Start the engine of the rescue vehicle. Turn the operating handle of the rescue vehicle to "discharge" Position so that the concrete in the failed vehicle can be discharged. After the emergency drive, restore the two vehicles to their original state.
2.減速機損壞。如在工作中出現減速機突然損壞,首先需將攪拌筒內的混凝土排出,以防出現凝固現象;其次再更換減速機,也可聯係生產廠家。
2. The reducer is damaged. If the reducer is suddenly damaged during operation, first discharge the concrete in the mixing drum to prevent solidification; Secondly, replace the reducer, or contact the manufacturer.
3.柱塞泵發生故障。非裝載時換上新的柱塞泵,使拌筒恢複正常運轉。
3. The plunger pump fails. When not loaded, replace with a new plunger pump to restore the normal operation of the mixing drum.
4.液壓管接頭處滲漏。將接頭拆下,更換密封圈,重新擰緊即可。
4. Leakage at the hydraulic pipe joint. Remove the connector, replace the sealing ring and retighten it.

截屏,微信識別二維碼