攪拌車的液壓泵吸油口應安裝粗濾器，吸油口應與油箱底部有一定距離； 攪拌車出油口應安裝高壓精濾器，過濾效果應滿足係統工作要求，防止汙染。 物料堵塞引起的液壓係統故障； 過濾網應安裝在攪拌車的液壓油箱隔板上，以去除回油過濾器未過濾的雜質。
The oil suction port of the hydraulic pump of the mixer truck should be installed with a coarse filter, and the oil suction port should be a certain distance from the bottom of the oil tank; High pressure fine filter shall be installed at the oil outlet of the mixer truck, and the filtering effect shall meet the working requirements of the system to prevent pollution. Hydraulic system failure caused by material blockage; The filter screen shall be installed on the diaphragm of the hydraulic oil tank of the mixer truck to remove the unfiltered impurities of the oil return filter.
攪拌車的液壓缸上應安裝金屬保護圈，防止汙物帶入缸內，防止泥水和光輻射侵蝕液壓缸造成泄漏； 液壓元件安裝前應檢查、清洗內鐵。 灰塵和雜質； 定期檢查液壓油，一旦油液變質、起泡、沉澱、油水分離等，應立即清洗係統並換油。
A metal protective ring shall be installed on the hydraulic cylinder of the mixer truck to prevent dirt from entering the cylinder and prevent leakage caused by muddy water and light radiation erosion of the hydraulic cylinder; Check and clean the inner iron before installing the hydraulic components. Dust and impurities; Check the hydraulic oil regularly. Once the oil deteriorates, bubbles, precipitates, oil-water separation, etc., clean the system and change the oil immediately.
新油加入攪拌車油箱前，應先靜置過濾後再加入。 必要時可設置中間油箱，用於新油的沉澱和過濾。
Before the new oil is added into the oil tank of the mixer truck, it should be filtered before adding. If necessary, an intermediate oil tank can be set for sedimentation and filtration of new oil.
避免“高檔低速”駕駛，這使得油料不完全燃燒，從而積累在油管內形成油泥。一定不要長時間的怠速運轉和低速行駛，這樣是 容易使得油料不完全燃燒，積累形成碳層。使用純淨度和品質達標的油料，油料的純度高，是的油料能夠快速充分的燃燒，這樣就會減少油泥的生成量。因此，使用匹配的小型混凝土攪拌車油料顯得十分有必要了。
Avoid "high-grade and low-speed" driving, which makes the oil incomplete combustion, thus accumulating in the oil pipe to form sludge. Do not idle for a long time and drive at a low speed, which is easy to cause incomplete combustion of oil and accumulation of carbon layer. Use the oil with purity and quality up to standard. The purity of the oil is high. Yes, the oil can burn quickly and fully, which will reduce the amount of sludge. Therefore, it is very necessary to use matching small concrete mixer oil.
在使用操作過程中避免單向閥堵死。這樣會引起箱殼內溫度升高，油氣排放不出去，從而殼內壓力升高潤滑油消耗增加。定期做檢查，有些易耗件須更換，比如及時更換失效油封，有些油封老化而失去彈性。拆裝或者更換部件時解決各類油管接頭密封。經常拆裝，容易滑絲斷扣而鬆脫，導致滲油。
Avoid blocking the check valve during use and operation. This will cause the temperature in the tank shell to rise and the oil and gas will not be discharged, so the pressure in the shell will rise and the lubricating oil consumption will increase. Check regularly, and some consumables need to be replaced, such as replacing the invalid oil seal in time. Some oil seals are aging and lose elasticity. Solve the sealing of various oil pipe joints when disassembling or replacing parts. Often disassembled, it is easy for the sliding wire to break and loosen, resulting in oil leakage.
避免攪拌車輪轂甩油，車輪轂軸承及腔內潤滑油脂過多，質量不良及老化失效。小型混凝土攪拌車製動過於頻繁導致輪轂溫度過高。
Avoid oil spilling from the mixer wheel hub, excessive lubricating grease in the wheel hub bearing and cavity, poor quality and aging failure. Too frequent braking of small concrete mixer leads to excessive hub temperature.
以上就是問題解答的相關內容了，希望能夠幫助到大家，如對這一問題還存在任何疑問，都歡迎關注kaiyun網站http://www.skar-bnat.com並谘詢kaiyun的工作人員，將竭誠為您服務。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.skar-bnat.com And consult our staff, will serve you wholeheartedly.
