Since the loading mixer truck, the gear beating of the mixer bucket loader generally occurs in the conflict project between the gearbox gears. Generally speaking, the gear beating will occur in the manual gearbox. Do you know why the gear beating of the manual mixer bucket occurs? Generally speaking, there will be synchronizer in the vehicle. Its function is to synchronize the high-speed gear with the gear that is about to enter the current gear.
咱們都知道在倒擋的狀況下，發生打齒現象的次數反而會增加，這主要由於在攪拌鬥中未裝置同步器，因此在中止狀態下，齒輪之間的差速器會隨之變小，這樣倒擋就會比較順暢。
We all know that under the condition of reverse gear, the number of tooth beating will increase. This is mainly because the synchronizer is not installed in the mixing bucket. Therefore, under the suspension state, the differential between gears will become smaller, so the reverse gear will be more smooth.
自上料攪拌車攪拌鬥裝載機出現打齒問題除了螺旋傘齒、齧合副自身質量、調整間隙不妥外，不正確的操作過程是導致拌和鬥出現打齒問題的主要原因。
In addition to the improper quality of spiral bevel gear, meshing pair and adjustment clearance, the incorrect operation process is the main reason for the toothing problem of mixing bucket.
自上料攪拌車 攪拌鬥裝載機在正常狀況下，自上料攪拌車一般多少錢一台，作業時前後橋一起驅動。若出現*載、後橋離地等現象，其悉數負荷由前橋接受，前橋的主減速器很簡單出現損壞現象。
Under normal conditions, how much is a self loading mixer? The front and rear axles are driven together during operation. In case of * load, rear axle off the ground and other phenomena, all the load is accepted by the front axle, and the main reducer of the front axle is very simple to be damaged.
假如門架傾翻切入角過大，門架放置的過低，很簡單發生前橋離地問題，悉數負荷由後橋接受，這時簡單發生後橋主減速器損壞。而主減速器損壞八成由於斷齒而發生了異響狀況。
If the entry angle of gantry tipping is too large and the gantry is placed too low, the problem of front axle off the ground simply occurs, and all the load is accepted by the rear axle. At this time, the main reducer of the rear axle is simply damaged. The main reducer is damaged, and 80% of them have abnormal noise due to broken teeth.
自上料攪拌車攪拌鬥裝載機不僅是叉車用利用的設備，一起拌和鬥裝載機還能夠出現一車多用途的現象。比如在插齒上裝置拌和鬥，攪拌鬥不使用了再將攪拌鬥從插齒上抽出來作為裝載機進行使用。快捷不說了，一起還省事、省時、省力且牢靠。若客戶自己家中有裝載機隻購買攪拌鬥也是能夠的。
The mixer bucket loader of self loading mixer truck is not only the equipment used by forklift, but also can be used for multiple purposes. For example, a mixing bucket is installed on the gear shaper. When the mixing bucket is not used, the mixing bucket is extracted from the gear shaper and used as a loader. Not to mention fast, it is also easy, time-saving, labor-saving and reliable together. If the customer has a loader at home, it is also possible to buy only a mixing bucket.
