With the continuous expansion of highway, railway and urban road construction projects, the company's construction market is gradually expanding need to use concrete, and concrete mixer is a common construction equipment, but the use of the process of problems are not less, such as equipment axle problems. So let's analyze it.
混凝土攪拌車抱軸的原因：
Reasons for holding the shaft of concrete mixer truck:
攪拌機抱軸是由於在攪拌過程中粉料、砂石和液體混合所形成的粘結物，黏附在攪拌軸和攪拌臂上，日積月累在其表麵形成一層非常厚且不易清理的粘結物。
The agitator holds the shaft because in the process of mixing powder, sand and liquid formed by the mixture of adhesives, adhesion to the mixing shaft and the mixing arm, accumulated over a long period of time on its surface to form a layer of very thick and difficult to clean the adhesives.
混凝土攪拌車抱軸的危害：
Harm of concrete mixing truck holding shaft:
混凝土攪拌車廠家認為影響混凝土的質量，攪拌機抱軸後打出的混凝土攪拌不均勻。增加了混凝土攪拌車的負載，耗能增大。影響耐磨件、軸端密封的壽命，加快耐磨件的磨損，抱軸後攪拌臂磨損非常嚴重，使用壽命大大縮短。
Concrete mixer manufacturer thinks that the quality of concrete is affected, and the concrete produced after the mixer holds the shaft is not evenly mixed. The load of concrete mixer is increased and the energy consumption is increased. It affects the life of wear-resistant parts and shaft end seal, speeds up the wear of wear-resistant parts, and the wear of the stirring arm after holding the shaft is very serious, and the service life is greatly shortened.
防止混凝土攪拌車抱軸的方法：
Methods to prevent the concrete mixer from holding the shaft:
調整喂食順序和時間。骨料和粉料預先混合後落入主機（但骨料必須先下一部分），使粉料在一定程度上附著在骨料上，減少落入主機的粉料。提高攪拌軸和攪拌臂的攪拌效率是可能的，也是可能的。
Adjust feeding order and time. The aggregate and powder are pre-mixed and then fall into the host (but the aggregate must be part of the next), so that the powder is attached to the aggregate to a certain extent, reducing the powder falling into the host. It is possible and possible to improve the mixing efficiency of the mixer shaft and the mixer arm.
主蓋水管中心線要求與攪拌軸中心線在同一垂直平麵內，攪拌臂與攪拌軸夾角上方有直噴噴嘴。因為攪拌臂與轉軸的夾角是最容易粘膠的地方，所以通常從攪拌臂根部開始抱軸。同時，始終需要加水的時間。
The center line of the water pipe of the main cover shall be in the same vertical plane as the center line of the mixing shaft, and there shall be a direct spray nozzle above the Angle between the mixing arm and the mixing shaft. Because the Angle between the stirring arm and the rotating shaft is the easiest place to stick, the shaft is usually held from the root of the stirring arm. Also, it always takes time to add water.
攪拌出料後，設備操作人員應及時清洗、衝洗罐體，以確保清除粘附的混凝土。設備操作人員應定期檢查計量係統中計量桶的連接和密封情況，注意是否有泄漏，如有則及時排除。
After mixing and discharging, equipment operators should clean and flush the tank in time to ensure the removal of adhesive concrete. Equipment operators should periodically check the connection and sealing of the metering barrels in the metering system to check whether there is leakage. If there is leakage, remove it in time.
當您在使用混凝土攪拌車的過程中遇到抱軸現象，一定要及時查明具體原因，以便快速解決，以免影響您的正常工作。更多相關文問題就來http://www.skar-bnat.com網站谘詢吧！
When you encounter the phenomenon of holding the axle in the process of using the concrete mixer, you must find out the specific reason in time, so as to solve it quickly, so as not to affect your normal work. More related questions come to http://www.skar-bnat.com website consultation!
